| 路由器（Router）是連接兩個或多個網絡的硬件設備，在網絡間起網關的作用，是讀取每一個數據包中的地址然后決定如何傳送的專用智能性的網絡設備，路由器最主要的功能為實現信息的轉送。 Cisco胖AP配置，思科胖AP配置，思科AP配置，思科AP常用配置，思科AP配置實例
主要配置命令
hostname ap /設置AP名
dot11 ssid AP-N2 /設置SSID（AP-N2為SSID號）
authentication open /認證開放
authentication key-management wpa version 2 /認證密鑰版本為WPA版本2
guest-mode /顯示SSID，no guest-mode表示隱藏SSID
wpa-psk ascii 123456789 /SSID登陸密鑰設置（123456789為密鑰）
exit
interface dot11radio0 /進入2.4G接口
encryption mode ciphers aes-ccm /加密密碼AES CCM模式
ssid AP-N2 /加入SSID AP-N2
power local maximum /設置AP信號發射功率，默認可不配置
no shutdown /開啟端口
exit
interface dot11radio1 /進入5.8G接口
encryption mode ciphers aes-ccm /加密密碼AES CCM模式
ssid AP-N2 /加入SSID AP-N2
power local maximum /設置AP信號發射功率，默認可不配置
no shutdown /開啟端口
exit
interface BVI1 進入管理接口
ip address 192.168.0.191 255.255.255.0 /配置接口IP地址
no shutdown /開啟端口
ip default-gateway 192.168.0.1 /配置網關
配置范例
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
!
hostname test-ap
!
logging rate-limit console 9
enable secret 5 $5$4fXI$i1Zl2wBy24uDQd2j2Tuf41
!
no aaa new-model
clock timezone BeiJing 8 0
no ip source-route
no ip cef
!
dot11 syslog
!
dot11 ssid testssid
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 1443130D010939102541
!
dot11 guest
!
username myname secret 5 $4$7p8Z$yjeef33iW422J3bDrdN8Q/
!
bridge irb
!
interface Dot11Radio0
no ip address
no shutdown
!
encryption mode ciphers aes-ccm
!
ssid testssid
!
antenna gain 0
power local maximum
packet retries 64 drop-packet
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
!
encryption mode ciphers aes-ccm
!
ssid testssid
!
no shutdown
!
antenna gain 0
power local maximum
peakdetect
dfs band 3 block
packet retries 64 drop-packet
bridge-group 1
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
!
interface GigabitEthernet1
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.0.16 255.255.255.0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
!
ip default-gateway 192.168.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
snmp-server community public RO
bridge 1 route ip
!
line con 0
line vty 0 4
login local
transport input all
!
sntp server 192.168.0.1
end
本文可以幫助您基本地設置和管理您的路由器。
| 
